Changeset 7561 in ntrip for trunk

Timestamp:

Oct 28, 2015, 11:02:02 PM (8 years ago)

Author:

weber

Message:

Documentation completed

File:

• trunk/BNC/src/bncwindow.cpp (modified) (3 diffs)

trunk/BNC/src/bncwindow.cpp

@@ -888 +888 @@
   pppLayout1->addWidget(_pppWidgets._antexFile,              ir, 4, 1, 3);
   ++ir;
-  pppLayout1->addWidget(new QLabel("Coordinates"),           ir, 0);
+  pppLayout1->addWidget(new QLabel("Coordinates file"),      ir, 0);
   pppLayout1->addWidget(_pppWidgets._crdFile,                ir, 1);
   pppLayout1->addWidget(new QLabel("   Version 3 filenames"),ir, 3);
@@ -914 +914 @@
   _pppWidgets._corrMount->setWhatsThis(tr("<p>Specify a 'mountpoint' from the 'Streams' canvas below which provides corrections to Broadcast Ephemeris.</p><p>If you don't specify a corrections stream through this option, BNC will fall back to Single Point Positioning (SPP, positioning from observations and broadcast ephemeris only only) instead of doing PPP.</p>"));
 
-  _pppWidgets._crdFile->setWhatsThis(tr("<p>Enter the full path to an ASCII file which specifies the streams or files of those stations you want to process. Specifying a 'Coordinates' file is optional. If it exists, it should contain one record per station with the following parameters separated by blank characters:<p><ul><li>Specify the station either through<ul><li>the 'Mountpoint' of the station's RTCM stream (when in real-time PPP mode), or</li><li>the 4-charater station ID of the RINEX observations file (when in post processing PPP mode).</li></ul></li><li>Approximate X,Y,Z coordinate components of station's Antenna Reference Point [m] (ARP, specify '0.0 0.0 0.0' if unknown).</li><li>Nort, East and Up component of antenna excentricity [m] (specify '0.0 0.0 0.0' if unknown).</li><li>20 Characters describing the antenna type and radome following the IGS 'ANTEX file' standard (leave blank if unknown).</li></ul></p><p>Records with exclamation mark '!' in the first column or blank records will be interpreted as comment lines and ignored.</p>"));
+  _pppWidgets._crdFile->setWhatsThis(tr("<p>Enter the full path to an ASCII file which specifies the streams or files of those stations you want to process. Specifying a 'Coordinates' file is optional. If it exists, it should contain one record per station with the following parameters separated by blank characters:<p><ul><li>Specify the station either through<ul><li>the 'Mountpoint' of the station's RTCM stream (when in real-time PPP mode), or</li><li>the 4-charater station ID of the RINEX observations file (when in post processing PPP mode).</li></ul></li><li>Approximate X,Y,Z coordinate components of station's Antenna Reference Point [m] (ARP, specify '0.0 0.0 0.0' if unknown).</li><li>Nort, East and Up component of antenna excentricity [m] (specify '0.0 0.0 0.0' if unknown).</li><li>20 Characters describing the antenna type and radome following the IGS 'ANTEX file' standard (leave blank if unknown).</li><li>Receiver type following the naming conventions for IGS equipment.</li></ul></p><p>Records with exclamation mark '!' in the first column or blank records will be interpreted as comment lines and ignored.</p>"));
 
   _pppWidgets._antexFile->setWhatsThis(tr("<p>Observations in RTCM streams or RINEX files should be referred to the receiver's and to the satellite's Antenna Phase Center (APC) and therefore be corrected for<ul><li>Receiver APC offsets</li><li>Receiver APC variations</li><li>Satellite APC offsets.</li></ul> Specify the full path to an IGS 'ANTEX file' which contains APC offsets and variations.</p><p>If you don't specify an 'ANTEX file' then observations will not be corrected for APC offsets and variations.</p>"));
@@ -951 +951 @@
   _pppWidgets._minEle->setWhatsThis(tr("<p>Select a Minimum satellite Elevation for observations.</p><p>BNC will ignore an observation if the associated Satellite Elevation does not reach or exceed this minimum.</p><p>Selecting '10 deg' may be an appropriate choise in order to avoid too noisy observations."));
 
-  _pppWidgets._lcGPS->setWhatsThis(tr("<p>Specify which kind of GPS observations you want to use and on which kind of ionosphere-free linear combination of GPS observations you want to base ambiguity resolutions.</p><p><ul><li>Specifying 'P3' means that you request BNC to use code data and the so-called P3 ionosphere-free linear combination of code observations.</li><li>'L3' means that you request BNC to use phase data and the so-called L3 ionosphere-free linear combination of phase observations.</li> <li>'P3&L3' means that you request BNC to use both, code and phase data and the so-called P3 and L3 ionosphere-free linear combination of code and phase observations.</li></ul></p><p>Note that most geodetic receivers support the observation of GPS code and phase data. Hence specifying 'P3&L3' would be a good choice when processing data from such a receiver.</p><p>Specifying 'no' means that you don't want BNC to use GPS data.</p>"));
+  _pppWidgets._lcGPS->setWhatsThis(tr("<p>Specify which kind of GPS observations you want to use and on which kind of ionosphere-free linear combination of GPS observations you want to base ambiguity resolutions.</p><p><ul><li>Specifying 'P3' means that you request BNC to use code data and the so-called P3 ionosphere-free linear combination of code observations.</li><li>'P3&L3' means that you request BNC to use both, code and phase data and the so-called P3 and L3 ionosphere-free linear combination of code and phase observations.</li></ul></p><p>Note that most geodetic receivers support the observation of GPS code and phase data. Hence specifying 'P3&L3' would be a good choice when processing data from such a receiver.</p><p>Specifying 'no' means that you don't want BNC to use GPS data.</p>"));
 
   _pppWidgets._lcGLONASS->setWhatsThis(tr("<p>Specify which kind of GLONASS observations you want to use and on which kind of ionosphere-free linear combination of GLONASS observations you want to base ambiguity resolutions.</p><p><ul><li>Specifying 'P3' means that you request BNC to use code data and the so-called P3 ionosphere-free linear combination of code observations.</li><li>'L3' means that you request BNC to use phase data and the so-called L3 ionosphere-free linear combination of phase observations.</li> <li>'P3&L3' means that you request BNC to use both, code and phase data and the so-called P3 and L3 ionosphere-free linear combination of code and phase observations.</li></ul></p><p>Specifying 'no' means that you don't want BNC to use GLONASS data.</p>"));