Changeset 6696 in ntrip


Ignore:
Timestamp:
Mar 19, 2015, 2:04:32 PM (7 years ago)
Author:
weber
Message:

Documentation completed

File:
1 edited

Legend:

Unmodified
Added
Removed
  • trunk/BNC/src/bncwindow.cpp

    r6691 r6696  
    12461246  _miscPortLineEdit->setWhatsThis(tr("BNC can output an incoming stream through a TCP/IP port of your local host. Specify a port number here to activate this function."));
    12471247  _scanRTCMCheckBox->setWhatsThis(tr("<p>Tick 'Scan RTCM' to log the numbers of incomming message types as well as contained antenna coordinates, antenna heigt, and antenna descriptor.</p><p>In case of RTCM Version 3 MSM streams, BNC will also log contained RINEX Version 3 observation types.</p>."));
    1248   _serialMountPointLineEdit->setWhatsThis(tr("<p>Enter a 'Mountpoint' to forward the corresponding stream to a serial connected receiver.</p>"));
     1248  _serialMountPointLineEdit->setWhatsThis(tr("<p>Enter a 'Mountpoint' to forward the corresponding stream to a serial connected receiver.</p><p>Depending on the stream contents the receiver may use it for Differential GNSS, Precise Point Positioning or any other purpose supported by the firmware.</p>"));
    12491249  _serialPortNameLineEdit->setWhatsThis(tr("<p>Enter the serial 'Port name' selected for communication with your serial connected receiver. Valid port names are</p><pre>Windows:       COM1, COM2<br>Linux:         /dev/ttyS0, /dev/ttyS1<br>FreeBSD:       /dev/ttyd0, /dev/ttyd1<br>Digital Unix:  /dev/tty01, /dev/tty02<br>HP-UX:         /dev/tty1p0, /dev/tty2p0<br>SGI/IRIX:      /dev/ttyf1, /dev/ttyf2<br>SunOS/Solaris: /dev/ttya, /dev/ttyb</pre><p>Note that you must plug a serial cable in the port defined here before you start BNC.</p>"));
    12501250  _serialBaudRateComboBox->setWhatsThis(tr("<p>Select a 'Baud rate' for the serial output link.</p><p>Note that your selection must equal the baud rate configured to the serial connected receiver. Note further that using a high baud rate is recommended.</p>"));
     
    12531253  _serialStopBitsComboBox->setWhatsThis(tr("<p>Select the number of 'Stop bits' for the serial output link.</p><p>Note that your selection must equal the number of stop bits configured to the serial connected receiver. Note further that often 1 stop bit is used.</p>"));
    12541254  _serialFlowControlComboBox->setWhatsThis(tr("<p>Select a 'Flow control' for the serial output link.</p><p>Note that your selection must equal the flow control configured to the serial connected receiver. Select 'OFF' if you don't know better.</p>"));
    1255   _serialAutoNMEAComboBox->setWhatsThis(tr("<p>Select 'no' if you don't want BNC to forward or upload any NMEA message to the NTRIP broadcaster following the 'Virtural Reference Station' concept.</p><p>Select 'Auto' to automatically forward NMEA messages of type GPGGA or GNGGA from your serial connected receiver to the NTRIP broadcaster and/or save them in a file.</p><p>Select 'Manual' if you want BNC to produce and upload one initial GPGGA NMEA message to the NTRIP broadcaster because your serial connected receiver doesn't generate these messages.</p>"));
     1255  _serialAutoNMEAComboBox->setWhatsThis(tr("<p>The 'NMEA' option supports the so-called 'Virtural Reference Station' (VRS) concept which requires the receiver to send approximate position information to the NTRIP Broadcaster. Select 'no' if you don't want BNC to forward or upload any NMEA message to the NTRIP broadcaster in support of VRS.</p><p>Select 'Auto' to automatically forward NMEA messages of type GPGGA or GNGGA from your serial connected receiver to the NTRIP broadcaster and/or save them in a file.</p><p>Select 'Manual' if you want BNC to produce and upload one initial GPGGA NMEA message to the NTRIP broadcaster because your serial connected receiver doesn't generate these messages.</p>"));
    12561256  _serialFileNMEALineEdit->setWhatsThis(tr("<p>Specify the full path to a file where NMEA messages coming from your serial connected receiver are saved.</p>"));
    12571257  _serialHeightNMEALineEdit->setWhatsThis(tr("<p>Specify an approximate 'Height' above mean sea level in meters for the reference station introduced through 'Mountpoint'. Together with the latitude and longitude from the NTRIP broadcaster sourcetable the height information is used to build one initial GPGGA message to be sent to the NTRIP broadcaster.</p><p>This option is only relevant when option 'NMEA' is set to 'Manual'.</p>"));
Note: See TracChangeset for help on using the changeset viewer.