Index: trunk/ntripserver/SiteLogExample.txt =================================================================== --- trunk/ntripserver/SiteLogExample.txt (revision 491) +++ (revision ) @@ -1,298 +1,0 @@ - RTBR Site Information Form - International GPS Service - See Instructions at: - ftp://igscb.jpl.nasa.gov/pub/station/general/sitelog_instr.txt - - -0. Form - - Prepared by (full name) : Roosbeek Fabian - Date Prepared : 2003-03-31 - Report Type : NEW - If Update: - Previous Site Log : - Modified/Added Sections : - - -1. Site Identification of the GNSS Monument - - Site Name : Brussels - Four Character ID : RTBR - Monument Inscription : - IERS DOMES Number : - CDP Number : (A4) - Monument Description : STEEL MAST - Height of the Monument : 8 m - Monument Foundation : CONCRETE BLOCK - Foundation Depth : 3 m - Marker Description : BRASS NAIL - Date Installed : 2003-02-28 - Geologic Characteristic : SAND - Bedrock Type : SEDIMENTARY - Bedrock Condition : FRESH - Fracture Spacing : 0 cm - Fault zones nearby : NO - Distance/activity : (multiple lines) - Additional Information : (multiple lines) - - -2. Site Location Information - - City or Town : Brussels - State or Province : Brabant - Country : Belgium - Tectonic Plate : Eurasian - Approximate Position (ITRF) - X coordinate (m) : 4027862.4040 - Y coordinate (m) : 307027.8440 - Z coordinate (m) : 4919508.3787 - Latitude (N is +) : +50.7982 - Longitude (E is +) : +004.3590 - Elevation (m,ellips.) : 00154.83 - Additional Information : (multiple lines) - - -3. GNSS Receiver Information - -3.1 Receiver Type : ASHTECH UZ-12 - Satellite System : GPS - Serial Number : ZR220023809 - Firmware Version : CJ00 - Elevation Cutoff Setting : 0 - Date Installed : 2003-02-28T09:00Z - Date Removed : CCYY-MM-DDThh:mmZ - Temperature Stabiliz. : 0.1 - Additional Information : - 2003-03-18T08:09Z Deactivation of smoothing - : in conversion from raw data to RINEX - : (XYZAshRx program) on request of IGS CB - -3.x Receiver Type : (A20, from rcvr_ant.tab; see instructions) - Satellite System : (GPS/GLONASS/GPS+GLONASS) - Serial Number : (A5) - Firmware Version : (A11) - Elevation Cutoff Setting : (deg) - Date Installed : (CCYY-MM-DDThh:mmZ) - Date Removed : (CCYY-MM-DDThh:mmZ) - Temperature Stabiliz. : (none or tolerance in degrees C) - Additional Information : (multiple lines) - - -4. GNSS Antenna Information - -4.1 Antenna Type : ASH701945E_M - Serial Number : CR620023301 - Antenna Reference Point : BPA - Marker->ARP Up Ecc. (m) : 000.0000 - Marker->ARP North Ecc(m) : 000.0000 - Marker->ARP East Ecc(m) : 000.0000 - Alignment from True N : - Antenna Radome Type : NONE - Radome Serial Number : - Antenna Cable Type : RGB233 - Antenna Cable Length : 50 - Date Installed : 2003-02-28T09:00Z - Date Removed : CCYY-MM-DDThh:mmZ - Additional Information : (multiple lines) - -4.x Antenna Type : (A20, from rcvr_ant.tab; see instructions) - Serial Number : (A*, but note the first A5 is used in SINEX) - Antenna Reference Point : - Marker->ARP Up Ecc. (m) : (F8.4) - Marker->ARP North Ecc(m) : (F8.4) - Marker->ARP East Ecc(m) : (F8.4) - Alignment from True N : (deg; + is clockwise/east) - Antenna Radome Type : (A4 from rcvr_ant.tab; see instructions) - Radome Serial Number : - Antenna Cable Type : (vendor & type number) - Antenna Cable Length : (m) - Date Installed : (CCYY-MM-DDThh:mmZ) - Date Removed : (CCYY-MM-DDThh:mmZ) - Additional Information : (multiple lines) - - -5. Surveyed Local Ties - -5.x Tied Marker Name : - Tied Marker Usage : (SLR/VLBI/LOCAL CONTROL/FOOTPRINT/etc) - Tied Marker CDP Number : (A4) - Tied Marker DOMES Number : (A9) - Differential Components from GNSS Marker to the tied monument (ITRS) - dx (m) : - dy (m) : - dz (m) : - Accuracy (mm) : (mm) - Survey method : (GPS CAMPAIGN/TRILATERATION/TRIANGULATION/etc) - Date Measured : (CCYY-MM-DDThh:mmZ) - Additional Information : (multiple lines) - - -6. Frequency Standard - -6.1 Standard Type : INTERNAL - Input Frequency : - Effective Dates : 2003-02-28/CCYY-MM-DD - Notes : (multiple lines) - -6.x Standard Type : (INTERNAL or EXTERNAL H-MASER/CESIUM/etc) - Input Frequency : (if external) - Effective Dates : (CCYY-MM-DD/CCYY-MM-DD) - Notes : (multiple lines) - - -7. Collocation Information - -7.x Instrumentation Type : (GPS/GLONASS/DORIS/PRARE/SLR/VLBI/TIME/etc) - Status : (PERMANENT/MOBILE) - Effective Dates : (CCYY-MM-DD/CCYY-MM-DD) - Notes : (multiple lines) - - -8. Meteorological Instrumentation - -8.1.x Humidity Sensor Model : - Manufacturer : - Serial Number : - Data Sampling Interval : (sec) - Accuracy (% rel h) : (% rel h) - Aspiration : (UNASPIRATED/NATURAL/FAN/etc) - Height Diff to Ant : (m) - Calibration date : (CCYY-MM-DD) - Effective Dates : (CCYY-MM-DD/CCYY-MM-DD) - Notes : (multiple lines) - -8.2.x Pressure Sensor Model : - Manufacturer : - Serial Number : - Data Sampling Interval : (sec) - Accuracy : (hPa) - Height Diff to Ant : (m) - Calibration date : (CCYY-MM-DD) - Effective Dates : (CCYY-MM-DD/CCYY-MM-DD) - Notes : (multiple lines) - -8.3.x Temp. Sensor Model : - Manufacturer : - Serial Number : - Data Sampling Interval : (sec) - Accuracy : (deg C) - Aspiration : (UNASPIRATED/NATURAL/FAN/etc) - Height Diff to Ant : (m) - Calibration date : (CCYY-MM-DD) - Effective Dates : (CCYY-MM-DD/CCYY-MM-DD) - Notes : (multiple lines) - -8.4.x Water Vapor Radiometer : - Manufacturer : - Serial Number : - Distance to Antenna : (m) - Height Diff to Ant : (m) - Calibration date : (CCYY-MM-DD) - Effective Dates : (CCYY-MM-DD/CCYY-MM-DD) - Notes : (multiple lines) - -8.5.x Other Instrumentation : (multiple lines) - - -9. Local Ongoing Conditions Possibly Affecting Computed Position - -9.1.x Radio Interferences : (TV/CELL PHONE ANTENNA/RADAR/etc) - Observed Degradations : (SN RATIO/DATA GAPS/etc) - Effective Dates : (CCYY-MM-DD/CCYY-MM-DD) - Additional Information : (multiple lines) - -9.2.x Multipath Sources : (METAL ROOF/DOME/VLBI ANTENNA/etc) - Effective Dates : (CCYY-MM-DD/CCYY-MM-DD) - Additional Information : (multiple lines) - -9.3.x Signal Obstructions : (TREES/BUILDLINGS/etc) - Effective Dates : (CCYY-MM-DD/CCYY-MM-DD) - Additional Information : (multiple lines) - - -10. Local Episodic Effects Possibly Affecting Data Quality - -10.x Date : (CCYY-MM-DDThh:mmZ) - Event : (TREE CLEARING/CONSTRUCTION/etc) - - -11. On-Site, Point of Contact Agency Information - - Agency : Royal Observatory of Belgium - Preferred Abbreviation : ROB - Mailing Address : Av. Circulaire No 3 - : B-1180 Brussels - Primary Contact - Contact Name : F. Roosbeek - Telephone (primary) : 32-2-373-02-46 - Telephone (secondary) : 32-2-373-02-11 - Fax : 32-2-374-98-22 - E-mail : f.roosbeek@oma.be - Secondary Contact - Contact Name : C. Bruyninx - Telephone (primary) : 32-2-373-02-92 - Telephone (secondary) : 32-2-373-02-11 - Fax : 32-2-374-98-22 - E-mail : c.bruyninx@oma.be - Additional Information : (multiple lines) - - -12. Responsible Agency (if different from 11.) - - Agency : (multiple lines) - Preferred Abbreviation : (A10) - Mailing Address : (multiple lines) - Primary Contact - Contact Name : - Telephone (primary) : - Telephone (secondary) : - Fax : - E-mail : - Secondary Contact - Contact Name : - Telephone (primary) : - Telephone (secondary) : - Fax : - E-mail : - Additional Information : (multiple lines) - - -13. More Information - - Primary Data Center : ROB - Secondary Data Center : - URL for More Information : - Hardcopy on File - Site Map : (Y or URL) - Site Diagram : (Y or URL) - Horizon Mask : - Monument Description : (Y or URL) - Site Pictures : - Additional Information : (multiple lines) - Antenna Graphics with Dimensions - -ASH701945E_M -Dorne Margolin with chokerings, Model 701945-01 REV E - - - +-------+ - / + \ <-- 0.1280 L2 - | + | <-- 0.1100 L1 - +-----------------+-------------+------------------+ <-- 0.1006 TCR - | | - | | - | | - | | -+-+--------------------------------------------------+-+ <-- 0.0376 -+-------------------+-------------+--------------------+ <-- 0.0346 BCR - | | - | | - +------x------+ <-- 0.0000 BPA=ARP - -<-- 0.3890 --> - - - ARP: Antenna Reference Point - L1 : L1 Phase Center L2 : L2 Phase Center - TCR: Top of Chokering BCR: Bottom of Chokering - BPA: Bottom of Preamplifier - Index: trunk/ntripserver/SiteLogInstr.txt =================================================================== --- trunk/ntripserver/SiteLogInstr.txt (revision 491) +++ (revision ) @@ -1,217 +1,0 @@ -Instructions for filling out IGS site logs -1 Dec 2003 (added Height Diff to Ant instructions) - -See log form at ftp://igscb.jpl.nasa.gov/pub/station/general/blank.log - -General -======= - -Please prepare site logs in plain ASCII. - -Line length is limited to 80 characters. - -See http://igscb.jpl.nasa.gov/network/sitelog-submissions.html for -submission instructions, or email your log to igscb.jpl.nasa.gov if -you prefer. Site logs emailed manually are usually handled by -the CB within about one business day. - -Date and time formats are ISO 8061; see http://www.iso.ch/markete/8601.pdf -As a summary, CC=2 digit century - YY=2 digit year - MM=2 digit month - DD=2 digit day of month - T=date/time separator - hh=2 digit hour - mm=2 digit minutes of hour - Z=UTC indicator - /=separator when begin & end times are given - -Latitude/Longitude formats are aligned to ISO 6709: - Lat: +/-DDMMSS.SS - Long: +/-DDDMMSS.SS -A + or - sign is required. Leading zeroes must be used as appropriate -to maintain the DDMMSS and DDDMMSS format. - -"etc" indicates you may enter any relevant answer, not just a choice -ofthe suggestions shown. - -"F7.4," "A4" and so on indicate the FORTRAN-style format which the -response should have. - Example 12345.7 = F7.1 - ABCD = A4 - -Blocks which have a "N.x" definition (namely sections 3-10) should -always have the complete historic set of information; when a change is -made, the previous information is left (for example in section 3.1) -and the new information is placed in a new block numbered 3.2. Please -leave the .x sections uncompleted to remind yourself of the format -when the next change occurs. - -Please remove the response hints such as "(F7.4 N/S)" as you fill out -the log (except in the .x sections and Date Removed fields for -currently installed equipment, which you will leave). If an -answer in an optional field is unknown, try to learn the answer for -the next log update. - -If you have any questions not answered here, please feel free to -contact the IGS Central Bureau:igscb@igscb.jpl.nasa.gov - -Special Instructions by section -================================ - -0. Form ------------ - -If Update: -Previous Site Log : (ssss_CCYYMMDD.log) - If the site already has a log at the IGS Central Bureau, enter - the filename currently found under - ftp://igscb.jpl.nasa.gov/pub/station/log/ - ssss = 4 character site name - -If Update: -Modified/Added Sections : (n.n,n.n,...) - Enter the sections which have changed from the previous version - of the log. Example: 3.2, 4.2 - -1. Site Identification of the GNSS Monument ---------------------------------------------- - -IERS DOMES Number : (A9) - This is strictly required. See - http://lareg.ensg.ign.fr/ITRF/domesreq.html to obtain one. - -Monument Description : (PILLAR/BRASS PLATE/STEEL MAST/FICTIVE/etc) - Enter one or more elements as necessary to describe the monument. - -Additional Information : (multiple lines) - Suggestions: electrical isolation - -2. Site Location Information ------------------------------ - -Approximate Position (ITRF) - This should be to a one meter precision. The elevation is to be -given as an F7.1 number representing an ellipsoidal height. - -3. GNSS Receiver Information --------------------------------------- - -Receiver Type : (A20, from rcvr_ant.tab; see instructions) - Please find your receiver in - ftp://igscb.jpl.nasa.gov/pub/station/general/rcvr_ant.tab and use - the official name, taking care to get capital letters, hyphens, - etc. exactly correct. If you do not find a listing for your - receiver, please notify the IGS Central Bureau - (igscb@igscb.jpl.nasa.gov). - -Serial Number : (A20) - Keep the 5 significant characters of the serial number field in - SINEX in mind: do not enter "S/N 12345" instead of "12345" since - valuable information will be lost. - -Firmware Version : (A11) - Keep the 11 significant characters of the field in SINEX in mind. - - Elevation Cutoff Setting : (deg) - Please respond with the tracking cutoff as set in the receiver, - regardless of terrain or obstructions in the area. - -Temperature Stabiliz. : (none or tolerance in degrees C.) - This refers to the temperature of the room in which the receiver - is housed. - -Date Removed : (CCYY-MM-DDThh:mmZ) - In the block for the receiver currently in operation, leave this - line as is to remind yourselt of the format when the next receiver - change is made. - -4. GNSS Antenna Information ---------------------------------------- - -Antenna Type : (A20 from rcvr_ant.tab; see instructions) - Please find your antenna in - ftp://igscb.jpl.nasa.gov/pub/station/general/rcvr_ant.tab and - use the official name, taking care to get capital letters, hyphens, - etc. exactly correct. If you do not find a listing for your - antenna, please notify the IGS Central Bureau - (igscb@igscb.jpl.nasa.gov). Please do not use antenna names from a - "Previously valid" section. Choose the corresponding new antenna - name. You may indicate a Radome code from rcvr_ant.tab in columns - 17-20 of the Antenna Type if desired. - -Serial Number : (A20) - Keep the 5 significant characters of the serial number field in - SINEX in mind: do not enter "S/N 12345" instead of "12345" since - valuable information will be lost. - -Antenna Reference Point : (BPA/BCR/XXX from "antenna.gra"; see instructions) - Locate your antenna in the file - ftp://igscb.jpl.nasa.gov/pub/station/general/antenna.gra - Indicate the three-letter abbreviation for the point which is - indicated equivalent to ARP for your antenna. Contact the Central - Bureau (igscb@igscb.jpl.nasa.gov) if your antenna does not appear. - -Marker->ARP Up Ecc. (m) : (F8.4) - This is the antenna height measured to an accuracy of 1mm - and defined as the vertical distance of the ARP from the marker - described in section 1. - -Alignment from True N : (deg; + is clockwise/east) - The positive direction is clockwise, so that due east - would be equivalent to a response of "+90" - -Antenna Radome Type : (A4 from rcvr_ant.tab; see instructions) - Place a Radome code from - ftp://igscb.jpl.nasa.gov/pub/station/general/rcvr_ant.tab here. - "NONE" indicates there is no radome. - -Date Removed : (CCYY-MM-DDThh:mmZ) - In the block for the antenna currently in operation, leave this - line as is to remind yourselt of the format when the next antenna - change is made. - -8. Meterological Information -------------------------------------------------------------- - Height Diff to Ant : (m) -This is sensor height minus antenna height. In other words, positive -if the sensor is above the antenna. Please note that this convention -was used in the Notes. - -12. Responsible Agency (if different from 9.) -------------------------------------------------------------- -The primary contacts listed here should always be the first choice for -questions about operation of the site. This person will receive -automated emails regarding site log or RINEX errors and should be -someone who can answer questions about the configuration and data -delivery for this site. - -13. More Information -------------------------------------------------------------- - Primary Data Center : - Secondary Data Center : -Please list the DC where the station's data ordinarily goes first as -"Primary." Use "Secondary" either for a second location where -the station's data always goes, or would go in the case of a -failure with the Primary DC. - - Additional Information: -Anything you feel is important. Some possibilities to consider are: -- Elevation mask table indicating physical mask effects such as - AZ ELEV AZ ELEV AZ ELEV AZ ELEV - 10 8 20 12 30 10 40 8 - 50 5 60 12 70 8 80 8 - 90 5 100 5 110 5 120 5 -130 5 140 5 150 8 160 8 -170 5 180 3 190 5 200 8 -210 8 220 8 230 5 240 5 -250 5 260 8 270 10 280 12 -290 12 300 12 310 12 320 8 -330 5 340 5 350 8 360 8 -(This could also be kept at your local www site and referred to -by URL in the log). - - - - -