Changeset 6957 in ntrip for trunk/BNC/src

Timestamp:

Jun 24, 2015, 1:28:31 PM (9 years ago)

Author:

weber

Message:

Documentation completed

File:

• trunk/BNC/src/bnchelp.html (modified) (6 diffs)

trunk/BNC/src/bnchelp.html

@@ -495 +495 @@
 &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; 3.15.8.3 <a href=#upclkrnx>RINEX </a><br>
 &nbsp; &nbsp; &nbsp; 3.15.9 <a href=#upcustom>Custom Trafo</a><br>
+&nbsp; &nbsp; &nbsp; 3.15.10 <a href=#upantex>ANTEX File</a><br>
 3.16. <a href=#upeph>Upload Ephemeris</a><br>
 &nbsp; &nbsp; &nbsp; 3.16.1 <a href=#brdcserver>Host &amp; Port</a><br>
@@ -2885 +2886 @@
 </p>
 <p>
-As an SP3 file contents should be referred to the satellites Center of Mass (CoM) while Broadcast Corrections are referred to the satellites APC, an offset has to be applied which is available from an IGS ANTEX file (see section 'ANTEX File'). You should therefore specify the 'ANTEX File' path under tab 'PPP (2)' if you want to save the stream contents in SP3 format. If you don't specify an 'ANTEX File' path there, the SP3 file contents will be referred to the satellites APCs.
+As an SP3 file contents should be referred to the satellites Center of Mass (CoM) while Broadcast Corrections are referred to the satellites APC, an offset has to be applied which is available from an IGS ANTEX file (see option 'ANTEX File' below). Hence you should specify the 'ANTEX File' path there if you want to save the stream contents in SP3 format. If you don't specify an 'ANTEX File' path, the SP3 file contents will be referred to the satellites APCs.
 </p>
 <p>
@@ -2962 +2963 @@
 <p><img src="IMG/screenshot26.png"/></p>
 <p><u>Figure 29:</u> Producing Broadcast Corrections from incoming precise orbits and clocks and uploading them to an NTRIP Broadcaster.</p>
+
+<p><a name="upantex"><h4>3.15.10 ANTEX File - mantatory if 'SP3 File' is specified</h4></p>
+<p>
+IGS provides a file containing absolute phase center variations for GNSS satellite and receiver antennas in ANTEX format. Entering the full path to such an ANTEX file is required here for referring the SP3 file contents to the satellite's Center of Mass (CoM). If you don't specify a ANTEX file the SP3 file will contain orbit information which is referred to Antenna Phase Center (APC) instead of CoM.
+</p>
 
 <p><a name="upeph"><h4>3.16. Upload Ephemeris</h4></p>
@@ -3107 +3113 @@
 <p><a name="streamuser"><h4>3.19.1.1.3 User and Password - mandatory for protected streams</h4></p>
 <p>
-Some streams on NTRIP Broadcasters may be restricted. Enter a valid 'User' ID and 'Password' for access to protected streams. Accounts are usually provided per NTRIP Broadcaster through a registration procedure. Register through <u>http://register.rtcm-ntrip.org</u> for access to protected streams from EUREF and IGS.
+Streams on NTRIP Broadcasters may be protected. Enter a valid 'User' ID and 'Password' for access to protected streams. Accounts are usually provided per NTRIP Broadcaster through a registration procedure. Register through <u>http://register.rtcm-ntrip.org</u> for access to protected streams from EUREF and IGS.
 </p>
 
@@ -3139 +3145 @@
 <ul>
 <li>Try using option '2' if your streams are otherwise blocked by a proxy server operated in front of BNC.</li>
+<li>When using NTRIP Version 2 via SSL (option '2s') you need to specify the appropriate 'Caster port' for that. It's usually port number 443.</li>
 <li>Option 'R' or 'U' may be selected if latency is more important than completeness for your application. Note that the latency reduction is likely to be in the order of 0.5 sec or less. Note further that options 'R' (RTSP/RTP mode) and 'U' (UDP mode) are not accepted by proxy servers and a mobile Internet Service Provider may not support it.</li>
 </ul>
@@ -3356 +3363 @@
 </li>
 <li>
-Drag and drop of configuration file is currently not supported on Mac OS X.
+Drag and drop of configuration files is currently not supported on Mac OS X. On such system you have to start BNC via command line.
 </li>