Changeset 6829 in ntrip

Timestamp:

May 12, 2015, 8:28:34 AM (9 years ago)

Author:

weber

Message:

Documentation completed

File:

• trunk/BNC/src/bncwindow.cpp (modified) (2 diffs)

trunk/BNC/src/bncwindow.cpp

@@ -901 +901 @@
   _pppWidgets._corrMount->setWhatsThis(tr("<p>Specify a 'mountpoint' from the 'Streams' canvas below which provides corrections to Broadcast Ephemeris.</p><p>If you don't specify a corrections stream through this option, BNC will fall back to Single Point Positioning (SPP, positioning from observations and broadcast ephemeris only only) instead of doing PPP.</p>"));
 
-  _pppWidgets._crdFile->setWhatsThis(tr("<p>Enter the full path to an ASCII file which specifies the streams or files of those stations you want to process. The 'Coordinates' file must contain one record per station with the following parameters separated by blank characters:<p><ul><li>Either<ul><li>the 'Mountpoint' of the station's RTCM stream (when in real-time PPP mode) or</li><li>the first four characters of the RINEX observations file (when in post processing PPP mode).</li></ul>This parameter is mandatory. BNC will carry out PPP solutions only for those stations which are listed here.</li><li>Approximate X,Y,Z coordinate components of station's Antenna Reference Point [m] (ARP, specify '0.0 0.0 0.0' if unknown).</li><li>Nort, East and Up component of antenna excentricity [m] (specify '0.0 0.0 0.0' if unknown).</li><li>20 Characters describing the antenna type and radome following the IGS 'ANTEX file' standard (leave blank if unknown).</li></ul></p><p>Records with exclamation mark '!' in the first column or blank records will be interpreted as comment lines and ignored.</p>"));
+  _pppWidgets._crdFile->setWhatsThis(tr("<p>Enter the full path to an ASCII file which specifies the streams or files of those stations you want to process. The 'Coordinates' file must contain one record per station with the following parameters separated by blank characters:<p><ul><li>Specify the station either through<ul><li>the 'Mountpoint' of the station's RTCM stream (when in real-time PPP mode), or</li><li>the first four characters of the RINEX observations file (when in post processing PPP mode).</li></ul>This parameter is mandatory. BNC will carry out PPP solutions only for those stations which are listed here.</li><li>Approximate X,Y,Z coordinate components of station's Antenna Reference Point [m] (ARP, specify '0.0 0.0 0.0' if unknown).</li><li>Nort, East and Up component of antenna excentricity [m] (specify '0.0 0.0 0.0' if unknown).</li><li>20 Characters describing the antenna type and radome following the IGS 'ANTEX file' standard (leave blank if unknown).</li></ul></p><p>Records with exclamation mark '!' in the first column or blank records will be interpreted as comment lines and ignored.</p>"));
 
   _pppWidgets._antexFile->setWhatsThis(tr("<p>Observations in RTCM streams or RINEX files should be referred to the receiver's and to the satellite's Antenna Phase Center (APC) and therefore be corrected for<ul><li>Receiver APC offsets</li><li>Receiver APC variations</li><li>Satellite APC offsets.</li></ul> Specify the full path to an IGS 'ANTEX file' which contains APC offsets and variations.</p><p>If you don't specify an 'ANTEX file' then observations will not be corrected for APC offsets and variations.</p>"));
@@ -925 +925 @@
   _pppWidgets._sigmaL1->setWhatsThis(tr("<p>Enter a sigma for your GNSS L1 phase observations in meters.</p><p>The higher the sigma you enter, the less the contribution of L1 phase observations to a PPP solutions based on a combination of code and phase data. 0.01 is likely to be an appropriate choice.</p>"));
 
-  _pppWidgets._maxResC1->setWhatsThis(tr("<p>Specify a maximum for residuals from C1 code observations in a PPP solution. '3.0' meters may be an appropriate choise for that.</p><p>If the maximum is exceeded contributions from the corresponding observation will be ignored in the PPP solution.</p>"));
-
-  _pppWidgets._maxResL1->setWhatsThis(tr("<p>Specify a maximum for residuals from L1 code observations in a PPP solution. '0.03' meters may be an appropriate choise for that.</p><p>If the maximum is exceeded contributions from the corresponding observation will be ignored in the PPP solution.</p>"));
+  _pppWidgets._maxResC1->setWhatsThis(tr("<p>Specify a maximum for residuals from C1 code observations in a PPP solution. '3.0' meters may be an appropriate choise for that.</p><p>If the maximum is exceeded, contributions from the corresponding observation will be ignored in the PPP solution.</p>"));
+
+  _pppWidgets._maxResL1->setWhatsThis(tr("<p>Specify a maximum for residuals from L1 code observations in a PPP solution. '0.03' meters may be an appropriate choise for that.</p><p>If the maximum is exceeded, contributions from the corresponding observation will be ignored in the PPP solution.</p>"));
 
   _pppWidgets._eleWgtCode->setWhatsThis(tr("<p>Tic 'Ele Wgt Code' to use satellite Elevation depending Weights for Code observations in the PPP solution.</p>"));