Changeset 1440 in ntrip

Timestamp:

Jan 5, 2009, 12:29:36 AM (15 years ago)

Author:

weber

Message:

* empty log message *

File:

• trunk/BNC/bncwindow.cpp (modified) (8 diffs)

trunk/BNC/bncwindow.cpp

@@ -307 +307 @@
   // ---------
   _proxyHostLineEdit->setWhatsThis(tr("<p>If you are running BNC within a protected Local Area Network (LAN), you might need to use a proxy server to access the Internet. Enter your proxy server IP and port number in case one is operated in front of BNC. If you do not know the IP and port of your proxy server, check the proxy server settings in your Internet browser or ask your network administrator.</p><p>Note that IP streaming is sometimes not allowed in a LAN. In this case you need to ask your network administrator for an appropriate modification of the local security policy or for the installation of a TCP relay to the NTRIP broadcasters. If these are not possible, you might need to run BNC outside your LAN on a network that has unobstructed connection to the Internet.</p>"));
-  _proxyPortLineEdit->setWhatsThis(tr("<p>If you are running BNC within a protected Local Area Network (LAN), you might need to use a proxy server to access the Internet. Enter your proxy server IP and port number in case one is operated in front of BNC. If you do not know the IP and port of your proxy server, check the proxy server settings in your Internet browser or ask your network administrator.</p><p>Note that IP streaming is sometimes not allowed in a LAN. In this case you need to ask your network administrator for an appropriate modification of the local security policy or for the installation of a TCP relay to the NTRIP broadcasters. If these are not possible, you might need to run BNC outside your LAN on a network that has unobstructed connection to the Internet.</p>"));
+  _proxyPortLineEdit->setWhatsThis(tr("<p>Enter your proxy server port number in case one is operated in front of BNC.</p>"));
   _waitTimeSpinBox->setWhatsThis(tr("<p>When feeding a real-time GNSS engine waiting for synchronized input epoch by epoch, BNC drops whatever is received later than 'Wait for full epoch' seconds. A value of 3 to 5 seconds is recommended, depending on the latency of the incoming streams and the delay acceptable to your real-time GNSS engine or products.</p><p>Note that 'Wait for full epoch' does not effect the RINEX Observation file content. Observations received later than 'Wait for full epoch' seconds will still be included in the RINEX Observation files.</p>"));
   _outFileLineEdit->setWhatsThis(tr("Specify the full path to a file where synchronized observations are saved in plain ASCII format. Beware that the size of this file can rapidly increase depending on the number of incoming streams."));
@@ -318 +318 @@
   _ephPathLineEdit->setWhatsThis(tr("Specify the path for saving Broadcast Ephemeris data as RINEX Navigation files. If the specified directory does not exist, BNC will not create RINEX Navigation files."));
   _corrPathLineEdit->setWhatsThis(tr("Specify a directory for saving Broadcast Ephemeris Correction files. If the specified directory does not exist, BNC will not create the files."));
-  _rnxScrpLineEdit->setWhatsThis(tr("<p>Whenever a RINEX Observation file is saved, you might want to compress, copy or upload it immediately via FTP. BNC allows you to execute a script/batch file to carry out these operations. To do that specify the full path of the script/batch file here. BNC will pass the full RINEX Observation file path to the script as a command line parameter (%1 on Windows systems, $1 onUnix/Linux systems).</p><p>The triggering event for calling the script or batch file is the end of a RINEX Observation file 'Interval'. If that is overridden by a stream outage, the triggering event is the stream reconnection.</p>"));
-  _rnxSkelLineEdit->setWhatsThis(tr("<p>Whenever BNC starts generating RINEX Observation files (and then once every day at midnight), it first tries to retrieve information needed for RINEX headers from so-called public RINEX header skeleton files which are derived from sitelogs. However, sometimes public RINEX header skeleton files are not available, its contents is not up to date, or you need to put additional/optional records in the RINEX header.</p><p>For that BNC allows using personal skeleton files that contain the header records you would like to include. You can derive a personal RINEX header skeleton file from the information given in an up to date sitelog. A file in the RINEX 'Directory' with the RINEX 'Skeleton extension' is interpreted by BNC as a personal RINEX header skeleton file for the corresponding stream.</p>"));
+  _rnxScrpLineEdit->setWhatsThis(tr("<p>Whenever a RINEX Observation file is saved, you might want to compress, copy or upload it immediately via FTP. BNC allows you to execute a script/batch file to carry out these operations. To do that specify the full path of the script/batch file here. BNC will pass the full RINEX Observation file path to the script as a command line parameter (%1 on Windows systems, $1 onUnix/Linux systems).</p>"));
+  _rnxSkelLineEdit->setWhatsThis(tr("<p>BNC allows using personal skeleton files that contain the header records you would like to include. You can derive a personal RINEX header skeleton file from the information given in an up to date sitelog. A file in the RINEX 'Directory' with the RINEX 'Skeleton extension' is interpreted by BNC as a personal RINEX header skeleton file for the corresponding stream.</p>"));
   _rnxAppendCheckBox->setWhatsThis(tr("<p>When BNC is started, new files are created by default and any existing files with the same name will be overwritten. However, users might want to append already existing files following a restart of BNC, a system crash or when BNC crashed. Tick 'Append files' to continue with existing files and keep what has been recorded so far.</p>"));
   _autoStartCheckBox->setWhatsThis(tr("<p>Tick 'Auto start' for auto-start of BNC at startup time in window mode with preassigned processing options.</p>"));
@@ -327 +327 @@
   _corrIntrComboBox->setWhatsThis(tr("<p>Select the length of the Broadcast Ephemeris Correction files.</p>"));
   _rnxSamplSpinBox->setWhatsThis(tr("<p>Select the RINEX Observation sampling interval in seconds. A value of zero '0' tells BNC to store all received epochs into RINEX.</p>"));
-  _binSamplSpinBox->setWhatsThis(tr("<p>Select the Observation sampling interval in seconds. A value of zero '0' tells BNC to send/store all received epochs.</p>"));
+  _binSamplSpinBox->setWhatsThis(tr("<p>Select the synchronized observation sampling interval in seconds. A value of zero '0' tells BNC to send/store all received epochs.</p>"));
   _obsRateComboBox->setWhatsThis(tr("<p>BNC can collect all returns (success or failure) coming from a decoder within a certain short time span to then decide whether a stream has an outage or its content is corrupted. The procedure needs a rough estimate of the expected 'Observation rate' of the incoming streams. When a continuous problem is detected, BNC can inform its operator about this event through an advisory note.</p><p>An empty option field (default) means that you don't want an explicit information from BNC about stream outages and incoming streams that can not be decoded and that the special procedure for handling of corrupted streams is bypassed.</p>"));
-  _adviseRecoSpinBox->setWhatsThis(tr("<p>Following a stream outage or a longer series of bad observations, an advisory note is generated when valid observations are received again throughout the 'Recovery threshold' time span. A value of about 5min (default) is recommended.</p><p>A value of zero '0' means that for any stream recovery, however short, BNC immediately generates an advisory note.</p><p>Note that for using this function you need to specify the 'Observation rate'.</p>"));
-  _adviseFailSpinBox->setWhatsThis(tr("<p>An advisory note is generated when no (or only corrupted) observations are seen throughout the 'Failure threshold' time span. A value of 15 min (default) is recommended.</p><p>A value of zero '0' means that for any stream failure, however short, BNC immediately generates an advisory note.</p><p>Note that for using this function you need to specify the 'Observation rate'.</p>"));
+  _adviseRecoSpinBox->setWhatsThis(tr("<p>Following a stream outage or a longer series of bad observations, an advisory note is generated when valid observations are received again throughout the 'Recovery threshold' time span. A value of about 5min (default) is recommended.</p><p>A value of zero '0' means that for any stream recovery, however short, BNC immediately generates an advisory note.</p>"));
+  _adviseFailSpinBox->setWhatsThis(tr("<p>An advisory note is generated when no (or only corrupted) observations are seen throughout the 'Failure threshold' time span. A value of 15 min (default) is recommended.</p><p>A value of zero '0' means that for any stream failure, however short, BNC immediately generates an advisory note.</p>"));
   _makePauseCheckBox->setWhatsThis(tr("<p>In case of a continuously corrupted stream, the decoding process can be paused and decodings are then attempted again at decreasing rate till the stream hopefully recovers. Tick 'Pause' to activate this function.</p><p>Do not tick 'Pause' (default) in order to prevent BNC from making any decoding pause. Be aware that this may incur an unnecessary workload.</p><p>Note that this function is only effective if an 'Observation rate' is specified.</p>"));
   _logFileLineEdit->setWhatsThis(tr("Records of BNC's activities are shown in the 'Logs' section on the bottom of this window. They can be saved into a file when a valid path is specified in the 'Logfile (full path)' field."));
-  _adviseScriptLineEdit->setWhatsThis(tr("<p>Specify the full path to a script or batch file to handle advisory notes generated in the event of corrupted streams or stream outages. The affected mountpoint and one of the comments 'Begin_Outage', 'End_Outage', 'Begin_Corrupted', or 'End_Corrupted' are passed on to the script as command line parameters.</p><p>The script can be configured to send an email to BNC's operator and/or to the affected stream provider. An empty option field (default) or invalid path means that you don't want to use this option.</p><p> Note that for using this function you need to specify the 'Observation rate'.</p>"));
+  _adviseScriptLineEdit->setWhatsThis(tr("<p>Specify the full path to a script or batch file to handle advisory notes generated in the event of corrupted streams or stream outages. The affected mountpoint and one of the comments 'Begin_Outage', 'End_Outage', 'Begin_Corrupted', or 'End_Corrupted' are passed on to the script as command line parameters.</p><p>The script can be configured to send an email to BNC's operator and/or to the affected stream provider. An empty option field (default) or invalid path means that you don't want to use this option.</p>"));
   _perfIntrComboBox->setWhatsThis(tr("<p>BNC can average latencies per stream over a certain period of GPS time. The resulting mean latencies are recorded in the 'Logs' section at the end of each 'Log latency' interval together with results of a statistical evaluation (approximate number of covered epochs, data gaps).</p><p>Select a 'Log latency' interval or select the empty option field if you do not want BNC to log latencies and statistical information.</p>"));
   _mountPointsTable->setWhatsThis(tr("<p>Streams selected for retrieval are listed in the 'Streams' section. Clicking on 'Add Streams' button will open a window that allows the user to select data streams from an NTRIP broadcaster according to their mountpoints. To remove a stream from the 'Streams' list, highlight it by clicking on it and hit the 'Delete Streams' button. You can also remove multiple streams by highlighting them using +Shift and +Ctrl.</p><p>BNC automatically allocates one of its internal decoders to a stream based on the stream's 'format' as given in the sourcetable. BNC allows users to change this selection by editing the decoder string. Double click on the 'decoder' field, enter your preferred decoder and then hit Enter. The accepted decoder strings are 'RTCM_2.x', 'RTCM_3.x', and 'RTIGS'.</p><p>In case you need to log the raw data as is, BNC allows users to by-pass its decoders and and directly save the input in daily log files. To do this specify the decoder string as 'ZERO'.</p><p>BNC can also retrieve streams from virtual reference stations (VRS). VRS streams are indicated by a 'yes' in the 'nmea' column. To initiate these streams, the approximate latitude/longitude rover position is sent to the NTRIP broadcaster. The default values can be change according to your requirement. Double click on 'lat' and 'long' fields, enter the values you wish to send and then hit Enter.</p>"));
@@ -437 +437 @@
     palette.setColor(_waitTimeSpinBox->backgroundRole(), Qt::lightGray);
     _waitTimeSpinBox->setPalette(palette);
-    palette.setColor(_outUPortLineEdit->backgroundRole(), Qt::lightGray);
-    _outUPortLineEdit->setPalette(palette);
     palette.setColor(_outFileLineEdit->backgroundRole(), Qt::lightGray);
     _outFileLineEdit->setPalette(palette);
@@ -444 +442 @@
     _binSamplSpinBox->setPalette(palette);
     _waitTimeSpinBox->setEnabled(false);
-    _outUPortLineEdit->setEnabled(false);
     _outFileLineEdit->setEnabled(false);
     _binSamplSpinBox->setEnabled(false);
@@ -1305 +1302 @@
   if (aogroup->currentIndex() == 5) {
     if (!isEmpty) {
-      palette.setColor(_outUPortLineEdit->backgroundRole(), Qt::white);
-      _outUPortLineEdit->setPalette(palette);
       palette.setColor(_outFileLineEdit->backgroundRole(), Qt::white);
       _outFileLineEdit->setPalette(palette);
@@ -1314 +1309 @@
       _binSamplSpinBox->setPalette(palette);
       _waitTimeSpinBox->setEnabled(true);
-      _outUPortLineEdit->setEnabled(true);
       _outFileLineEdit->setEnabled(true);
       _binSamplSpinBox->setEnabled(true);
     } else {
-      palette.setColor(_outUPortLineEdit->backgroundRole(), Qt::lightGray);
-      _outUPortLineEdit->setPalette(palette);
       palette.setColor(_outFileLineEdit->backgroundRole(), Qt::lightGray);
       _outFileLineEdit->setPalette(palette);
@@ -1327 +1319 @@
       _binSamplSpinBox->setPalette(palette);
       _waitTimeSpinBox->setEnabled(false);
-      _outUPortLineEdit->setEnabled(false);
       _outFileLineEdit->setEnabled(false);
       _binSamplSpinBox->setEnabled(false);